English English
Views: 86 Author: Site Editor Publish Time: 2021-09-20 Origin: Site
In our production and life, the automatic fabric spreader plays an important role in many operations. Our automatic fabric spreader needs maintenance, so how to perform technical maintenance on the automatic fabric spreading machine? Let's take a look together.
This is the content list:
l Daily technical maintenance
l Periodic technical maintenance
l Technical maintenance for long-term parking
To clean the automatic fabric spreader, it is necessary to remove the mud, sticky sand, and asphalt on the surface of the automatic fabric spreader. Remove dust and grease on the surface of the engine, hydraulic components, and other parts of the automatic fabric spreader. Be careful not to get dirt into the oil filler and air filter of the automatic fabric spreader. Check the nozzles, connecting pipes, gas tanks, and switches of the heating system of the automatic fabric spreader. Check the connection and fastening of the parts of the automatic fabric spreader, especially whether the connecting bolts of the left and right track beams and the frame, the screed, the distribution device and the scraper conveying device of the automatic fabric spreader are loose or broken. Tighten or replace when necessary. Check and eliminate the leakage of various parts of the automatic fabric spreader. Check the amount of engine oil, fuel, coolant, and hydraulic oil of the automatic fabric spreader engine, and add the new oil of the automatic fabric spreader to the indication mark of the oil mark according to the regulations. Check whether the amount of grease in the centralized lubrication device of the automatic fabric spreader is appropriate. Check whether there are cracks in the blades of the spiral distribution device of the automatic fabric spreader, and replace if there are any. Check whether the electrical plugs of the automatic fabric spreader are loose.
Technical maintenance of the automatic fabric spreader after 50 hours of running-in. Before being put into use, the automatic fabric spreader should be tested for 50 hours, otherwise, it must not be put into use. For the 50h running-in operation, it should be carried out by the relevant regulations in the operation manual of the automatic fabric spreader engine. After the running-in trial operation is over, the technical maintenance of the automatic fabric spreader must be carried out according to the following contents: replace the diesel engine oil of the automatic fabric spreader, drain the old engine oil when the automatic fabric spreader is warming up, and then inject the new engine oil. After the short-term operation of the automatic fabric spreader, immediately check whether the oil level of the automatic fabric spreader is at the specified height. Replace the lubricating oil in the transfer case and all reducers of the automatic fabric spreader. Drain the old lubricating oil when the automatic fabric spreader is warming up, and then inject new lubricating oil.
Replace the oil filter element of the automatic fabric spreader. Replace the filter element of the diesel fine filter of the automatic fabric spreader. Check whether the hydraulic oil of the automatic fabric spreader reaches the specified amount. Check the engine coolant level of the automatic fabric spreader, if it is insufficient, add to the specified amount. Check the nozzles, connecting pipes, gas tanks, and switches of the heating system of the automatic fabric spreader. Check whether there are cracks in the rubber track shoe of the automatic fabric spreader. If the crack length is greater than 50mm, it must be replaced. Check whether there is any leakage in the hydraulic system of the automatic fabric spreader, and remove it if necessary. The filter element of the air filter must be cleaned every 50 hours of operation of the diesel engine of the automatic fabric spreader. Check whether there are cracks in the blades of the spiral distribution device of the automatic fabric spreader, and replace if there are any. Check whether the automatic leveling device of the automatic fabric spreader is normal. Check whether there is leakage in each working cylinder of the automatic fabric spreader, and remove it if there is any.
If the automatic fabric spreader will be parked for 3 months, it should be maintained according to the following requirements. Carry out the technical maintenance of the automatic material paver for long-term parking according to the requirements in the instruction manual, and make the anti-rust treatment. Clean the inner and outer surfaces of the automatic fabric spreader, the hopper, the screed, the spiral distribution device, and the scraper conveying device. The automatic fabric spreader should be placed in a ventilated place and covered with canvas. Padded the screed of the automatic fabric spreader with wooden blocks. The hopper and leveling cylinder of the automatic material paver must be retracted. When the automatic fabric spreader is parked for a long time, only the basic section of the ironing device and the material distributing device can be installed on the main body of the automatic fabric spreader. The accessories of the automatic fabric spreader should be rust-proof after cleaning and placed in a clean and ventilated room. Add new lubricating oil or grease to each lubrication point of the automatic fabric spreader.
Wuhan TIMING Weiye Technology Co., Ltd. is the newest industrial company that provides automatic fabric spreader warranty service when it leaves the factory and provides many maintenance instructions for automatic fabric spreaders. If you are interested in automatic fabric spreader If you are interested in Timingcutter, please contact us, our website is https://www.timingcutter.com/.
