Publish Time: 2021-09-24 Origin: Site
The fabric cutting machine has tens of thousands or even hundreds of thousands of pieces for a piece of equipment, so you must pay attention to the fabric cutting machine operation, and usually pay attention to the maintenance and maintenance of the fabric cutting machine to increase the service life of the equipment, save costs, and create greater interest. So how to maintain the fabric cutting machine? Next, let's go take a look.
This is the content list:
l Water replacement and water tank cleaning
l Fan cleaning
l Lens cleaning
The water pump of the fabric cutting machine needs to be replaced every three hours. The water cooling of the fabric cutting machine chiller is changed once a day, and the fabric cutting machine air-cooled is changed once a week. The fabric cutting machine water tank is cleaned every week. Note: Make sure that the laser tube is filled with circulating water before the fabric cutting machine works.
The water quality and temperature of the circulating water of the fabric cutting machine directly affect the service life of the fabric cutting machine tube. It is recommended to use pure water and keep the water temperature below 35°C. If it exceeds 35°C, the circulating water needs to be replaced, or ice cubes are added to the water to lower the water temperature.
Cleaning the water tank of the fabric cutting machine: first, turn off the power of the fabric cutting machine, unplug the water inlet pipe of the fabric cutting machine, let the water in the fabric cutting machine automatically flow into the water tank, turn on the water tank of the fabric cutting machine, take out the water pump of the fabric cutting machine, and clear the fabric cutting machine Dirt on the water pump. Clean the water tank of the fabric cutting machine, replace the circulating water, restore the water pump of the fabric cutting machine to the water tank, insert the water pipe connected to the water pump of the fabric cutting machine into the water inlet, and arrange all joints. Separately power on the water pump of the fabric cutting machine and run for 2-3 minutes (make the fabric cutting machine full of circulating water).
Long-term use of the fabric cutting machine fan will accumulate a lot of solid dust in the fabric cutting machine fan, causing the fabric cutting machine fan to produce a lot of noise, and it is not conducive to exhaust and deodorization. When the fabric cutting machine has insufficient fan suction, first turn off the power of the fabric cutting machine, remove the air inlet and outlet pipes on the fabric cutting machine fan, remove the dust in the fabric cutting machine, and then set the fabric cutting machine Stand the fan upside down, and pull the cloth cutting typhoon blades inside until it is clean, and then install the fabric cutting machine fan.
There are 3 reflectors and 1 focusing mirror on the fabric cutting machine (No. 1 reflector is located at the emission exit of the laser tube, which is the upper left corner of the fabric cutting machine, and No. 2 reflectors are located at the left end of the crossbeam of the fabric cutting machine, No. 3 The reflecting mirror is located on the top of the fixed part of the fabric cutting machine head, and the focusing lens is located in the adjusmachine lens barrel under the laser head. The fabric cutting machine is reflected and focused by these lenses and emitted from the laser head. The lens of the fabric cutting machine is easily stained with dust or other contaminants, which may cause the loss of the fabric cutting machine or damage to the lens. When cleaning the No. 1 and No. 2 fabric cutting machine, the lens does not need to be removed, just wipe it with a cleaning fluid. The lens paper is carefully wiped along the center to the edge of the lens of the fabric cutting machine. The No. 3 lens and focusing lens need to be taken out of the frame of the fabric cutting machine, wipe in the same way, and put back on the fabric cutting machine as they are after wiping.
Note that the lens of the fabric cutting machine should be wiped gently, and the coating on the surface of the fabric cutting machine should not be damaged. The metal-wood coated lens is more durable. During the wiping process, the fabric cutting machine should be handled gently to prevent it from falling. When installing the focusing lens of the fabric cutting machine, be sure to keep the concave surface facing down.
Wuhan TIMING Weiye Technology Co., Ltd. is the newest industrial company to produce a better fabric cutting machine. It has also invested a lot in the maintenance of the fabric cutting machine. If you are interested in the fabric cutting machine, you can contact us, the website is https://www.timingcutter.com/.